MSDS Index
|
M
A T E R I A L S A F E T Y D A T A S H E E T
|
| ABPA
604 URETHANE ACTIVATOR (FAST) |
|
HMIS
CODES:
|
H |
F |
R |
P |
| PRODUCT
NAME: URETHANE ACTIVATOR (FAST) |
|
|
2
|
2
|
1 |
G |
| PRODUCT
CODE: ABPA 604 |
|
|
|
|
SECTION I - HAZARDOUS INGREDIENTS/SARA
III INFORMATION
|
|
|
VAPOR PRESSURE
|
WEIGHT |
| REPORTABLE
COMPONENTS |
CAS NUMBER
|
mm Hg @
TEMP |
PERCENT |
| n-Butyl
Acetate |
123-86-4 |
8.4 |
20 C |
30 - 35 |
|
OSHA PEL
150 ppm (TWA)/ 200 ppm (STEL) |
|
|
|
|
|
ACGIH TLV
150 ppm (TWA)/ 200 ppm (STEL) |
|
|
|
|
| * Toluene
|
108-88-3 |
38 |
20 C |
5 - 10 |
|
OSHA TWA
100 ppm |
|
|
|
|
| Ethyl Acetate
|
141-78-6 |
76 |
20 C |
5 - 10 |
| Aromatic
Hydrocarbon |
64742-95-6 |
< 1 |
20 C |
1 - 5 |
|
OSHA TWA
50 ppm |
|
|
|
|
| * 1,2,4-Trimethylbenzene |
95-63-6 |
38 |
20 C |
< 1 |
|
OSHA TWA
25 ppm |
|
|
|
|
| * 1,6-Hexamethylene
Diisocyanate |
822-06-0
|
< .01 |
20 C |
< 1 |
|
ACGIH TWA
.005 ppm |
|
|
|
|
Indicates
toxic chemical(s) subject to the reporting requirements of section 313 of Title
III and of 40 CFR 372. WARNING: DETECTABLE AMOUNTS OF A CHEMICAL KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE CANCER AND/OR BIRTH DEFECTS OR OTHER REPRODUCTIVE
HARM MAY BE PRESENT IN THIS PRODUCT.
SECTION II - PHYSICAL/CHEMICAL
CHARACTERISTICS
| BOILING
RANGE: 170 F - 320 F |
SPECIFIC
GRAVITY (H20=1): 1.01 |
| VAPOR DENSITY:
Heavier than air |
EVAPORATION
RATE: Slower than n-Butyl Acetate |
| COATING
V.O.C.: 3.84 lb/gal |
MATERIAL
V.O.C.: 3.84 lb/gal |
| SOLUBILITY
IN WATER: Non soluble |
APPEARANCE
AND ODOR: Water white clear liquid, Ester solvent odor. |
SECTION III - FIRE AND
EXPLOSION HAZARD DATA
| FLASH
POINT: 75.2 F |
|
METHOD
USED: TCC |
| FLAMMABLE
LIMITS IN AIR BY VOLUME: |
LOWER:
1.0 |
UPPER:
11 |
EXTINGUISHING MEDIA:
FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL, WATER FOG.
SPECIAL FIREFIGHTING
PROCEDURES: Respiratory equipment should be worn to avoid inhalation
of concentrated vapors. Water should not be used except as fog to keep nearby
containers cool.
UNUSUAL FIRE AND EXPLOSION
HAZARDS: Handle as flammable liquid. Vapors form explosive mixture
in air between upper and lower explosive limits which can be ignited by many
sources such as pilot lights, open flames, electrical motors and switches.
SECTION IV - REACTIVITY
DATA
STABILITY: Stable
CONDITIONS TO AVOID:
Excessive heat, poor ventilation, corrosive atmospheres, excessive age.
INCOMPATIBILITY (Materials
to avoid): Alkaline materials, strong acids, and oxidizing agents.
HAZARDOUS DECOMPOSITION
OR BYPRODUCTS: Carbon monoxide, carbon dioxide, oxides of nitrogen.
HAZARDOUS POLYMERIZATION:
Will Not Occur.
SECTION V - HEALTH HAZARD
DATA
INHALATION HEALTH RISKS
AND SYMPTOMS OF EXPOSURE: Inhalation: Dizziness, breathing difficulty, headache
& loss of coordination. May cause asthma-like symptoms, including
coughing, wheezing, tightness of chest, and shortness of breath.
SKIN AND EYE CONTACT HEALTH
RISKS AND SYMPTOMS OF EXPOSURE: Eye contact: severe irritation, tearing,
redness and blurred vision.
SKIN ABSORPTION HEALTH
RISKS AND SYMPTOMS OF EXPOSURE: Skin contact: Can dry and defat skin causing
cracks, irritation, and dermatitis.
INGESTION HEALTH RISKS
AND SYMPTOMS OF EXPOSURE: Ingestion: Can cause gastrointestinal irritation,
vomiting, nausea, and diarrhea.
HEALTH HAZARDS ( ACUTE
AND CHRONIC ): ACUTE: Inhalation - Dizziness,
breathing difficulty, headaches, & loss of coordination. Eye Contact
- Severe irritation, tearing, redness, and blurred vision. Skin Contact
- Can dry and defat skin causing cracks, irritation, and dermatitis. Ingestion
- Can cause gastrointestinal irritation, vomiting, nausea, and diarrhea.
CHRONIC: Repeated
and prolonged overexposure to solvents may lead to permanent brain and nervous
system damage.
CARCINOGENICITY :
NTP CARCINOGEN: NO
IARC MONOGRAPHS: NO OSHA REGULATED: NO
MEDICAL CONDITIONS GENERALLY
AGGRAVATED BY EXPOSURE: Anesthesia, respiratory tract
irritation, dermatitus, nausea, and vomiting.
EMERGENCY AND
FIRST AID PROCEDURES: Inhalation Overexposure
- Move person to fresh air. If breathing stops, apply artificial respiration
and seek immediate medical attention. Eye Contact - Flush with large quantities
of water for 15 minutes. Skin Contact - Wash thoroughly with soap and water,
and see a doctor. Ingestion - DO NOT induce vomiting, can cause chemical pneumonitis
and pulmonary edema. Contact physician immediately.
SECTION VI - PRECAUTIONS
FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN
IN CASE MATERIAL IS RELEASED OR SPILLED: Eliminate ignition sources,
provide good ventilation, dike spill area and add absorbent earth or sawdust
to spilled liquid.
WASTE DISPOSAL
METHOD: Collect absorbent/spilled
liquid mixture into metal container; cover and seal container. Consult local,
state, and federal hazardous waste regulations before disposing into approved
hazardous waste landfill. Obey relevant laws.
PRECAUTIONS TO
BE TAKEN IN HANDLING AND STORING: Use non-sparking utensils
when handling this material. Avoid hot metal surface. Use in cool, well ventilated
areas. Keep containers closed when not in use. Keep away from excessive heat
and open flames.
OTHER PRECAUTIONS:
Smoking in areas where
this material is used should be strictly prohibited. Tools used with this material
should be made from aluminum, brass, or copper. Plastic utensils should not
be used.
SECTION VII -
CONTROL MEASURES
RESPIRATORY PROTECTION:
When spraying this material
use a fresh-air supplying respirator or a self-contained breathing apparatus.
VENTILATION:
General mechanical ventilation
or local exhaust should be suitable to keep vapor concentrations below TLV.
Ventilation equipment must be explosion proof.
PROTECTIVE GLOVES:
Impermeable chemical handling
gloves for skin protection.
EYE
PROTECTION: Use chemical safety glasses,
goggles, and face shields for eye protection.
OTHER PROTECTIVE
CLOTHING OR EQUIPMENT: Use impermeable aprons
and protective clothing whenever possible to prevent skin contact. The use of
head caps whenever possible is strongly recommended.
WORK/HYGIENIC
PRACTICES: Eye washes and safety showers
in the workplace are recommended.
SECTION VIII -
DISCLAIMER
To the best of our knowledge,
the information contained herein is accurate, obtained from sources believed
by Cumberland Products Inc. to be accurate.