|
Keystone
MSDS Information
|
| |
|
M
A T E R I A L S A F E T Y D A T A S H E E T
|
| ABPA
991 BLACK ROCK GUARD |
|
NFPA
CODES:
|
H |
F |
R |
P |
| PRODUCT
NAME: BLACK ROCK GUARD |
|
|
2
|
4
|
0 |
B |
| PRODUCT
CODE: ABPA 991 |
|
|
|
|
SECTION
I - HAZARDOUS INGREDIENTS/SARA III INFORMATION
|
| |
|
WEIGHT |
| REPORTABLE
COMPONENTS |
CAS NUMBER
|
PERCENT |
| --------------------------------------------- |
----------------- |
-------------- |
| *
Toluene |
108-88-3 |
40 - 50 |
| |
OSHA TWA
100 ppm |
|
|
| |
ACGIH TLV
100 ppm |
|
|
| Acetone |
67-64-1 |
1 - 10 |
| |
OSHA PEL
750ppm |
|
|
| |
ACGIH TLV
750 ppm |
|
|
| Dimethyl
Ether |
115-10-6 |
20 - 30 |
| |
N / E |
|
|
| |
N / E
|
|
|
| |
|
|
|
* Indicates
toxic chemical(s) subject to the reporting requirements of section 313 of Title
III of the Super Fund Amendments and Reauthorization Act (SARA) and
of 40 CFR part 372.
WARNING: DETECTABLE AMOUNTS
OF A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND/OR BIRTH
DEFECTS OR OTHER REPRODUCTIVE
HARM MAY BE PRESENT IN THIS PRODUCT: Toluene.
DOT SHIPPING: ORM-D CONSUMER
COMMODITY
SECTION
II - PHYSICAL/CHEMICAL CHARACTERISTICS
| BOILING
RANGE: -13 F to 213 F |
SPECIFIC
GRAVITY (H20=1AT STP): 0.90 |
| VAPOR DENSITY:
Heavier than air |
EVAPORATION
RATE: 1+ (Water = 1) |
| COATING
V.O.C.: 4.17lb/gal |
MATERIAL
V.O.C.: 4.17 lb/gal |
| SOLUBILITY
IN WATER: Not Soluble |
VAPOR PRESSURE:
mmHg @ 70 F = 60 - 85 |
| APPEARANCE
AND ODOR: Black liquid, strong solvent odor |
%
VOC: 55.5% |
SECTION
III-FIRE AND EXPLOSION HAZARD DATA
| FLASH
POINT: -142.5 F |
|
METHOD
USED: TCC |
| FLAMMABLE
LIMITS IN AIR BY VOLUME: |
LOWER:
N / A |
UPPER:
N / A |
EXTINGUISHING
MEDIA: CLASS B EXTINGUISHER-FOAM, ALCOHOL
FOAM, C02, DRY CHEMICAL.
SPECIAL
FIREFIGHTING PROCEDURES
Firefighters
should were NIOSH approved positive pressure self-contained breathing apparatus.
Aerosol cans may rupture when heated.
UNUSUAL
FIRE AND EXPLOSION HAZARDS
Heated cans
may burst.
SECTION
IV- REACTIVITY DATA
STABILITY:
STABLE
CONDITIONS
TO AVOID
Heat,
sparks, and open flames.
INCOMPATIBILITY
(MATERIALS TO AVOID)
Strong
oxidizing agents. Strong acids, alkalis, oxidizers.
HAZARDOUS
DECOMPOSITION OR BYPRODUCTS
Normal
combustion products. Carbon Dioxide, Carbon Monoxide, and other noxious products
from burning hydrocarbons.
HAZARDOUS
POLYMERIZATION: WILL NOT OCCUR
SECTION
V-HEALTH HAZARD DATA
INHALATION
HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Inhalation:
Dizziness, breathing difficulty, headache, loss of coordination, loss of concentration.
EYE
CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye
contact: Severe irritation, tearing, redness and blurred vision.
SKIN
ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Skin
contact: Can dry and defat skin causing cracks, irritation, and dermatitis.
INGESTION
HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Ingestion:
Can cause gastrointestinal irritation, vomiting, nausea, and diarrhea.
HEALTH
HAZARDS (ACUTE AND CHRONIC)
ACUTE: Inhalation
- Dizziness, breathing difficulty, headaches, and loss of coordination. Eye
Contact - Severe irritation, tearing, redness, and blurred vision. Skin Contact
- Can dry and defat skin causing cracks, irritation, and dermatitis. Ingestion
- can cause gastrointestinal irritation, vomiting, & diarrhea.
CHRONIC:
Repeated and prolonged overexposure to solvents may lead to lung, liver, or
kidney damage. The solvents listed have been reported to affect the central
nervous system: Toluene.
CARCINOGENICITY:
NTP CARCINOGEN: No IARC MONOGRAPHS: No OSHA
REGULATED: No
MEDICAL
CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
If
you have a medical condition, consult a physician prior to using this product.
EMERGENCY
AND FIRST AID PROCEDURES
Inhalation
Overexposure - Move person to fresh air. If breathing stops, apply artificial
respiration and seek immediate medical attention.
Eye Contact
- Flush with large quantities of water for 15 minutes. Skin Contact - Wash thoroughly
with soap and water, and see a doctor.
Ingestion
- DO NOT induce vomiting, can cause chemical pneumonitis and pulmonary edema.
Contact physician immediately.
SECTION
VI-PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS
TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Eliminate
ignition sources, provide good ventilation, dike spill area and add absorbent
earth or sawdust to spilled liquid.
WASTE
DISPOSAL METHOD
Collect
absorbent/spilled liquid mixture into metal container; cover and seal container.
Consult local, state, and federal hazardous waste
regulations
before disposing into approved hazardous waste landfill. Obey relevant laws.
PRECAUTIONS
TO BE TAKEN IN HANDLING AND STORING
Use non-sparking
utensils when handling this material. Avoid hot metal surface. Use in cool,
well ventilated areas.
Keep containers
closed when not in use. Keep away from excessive heat and open flames. Store
at temperatures below 120 F. Keep out
of reach
of children.
OTHER
PRECAUTIONS
Smoking
in areas where this material is used should be strictly prohibited. Tools used
with this material should be made from aluminum,
brass,
or copper. Plastic utensils should not be used.
SECTION
VII - CONTROL MEASURES
RESPIRATORY
PROTECTION
When spraying
this material use a fresh-air supplying respirator or a self-containing breathing
apparatus.
VENTIALTION
General
mechanical ventilation or local exhaust should be suitable to keep vapor concentrations
below TLV. Ventilation equipment must be explosion proof.
PROTECTIVE
GLOVES
Impermeable
chemical handling gloves for skin protection, none required when spraying.
EYE
PROTECTION
Use chemical
safety glasses, goggles, and face shields for eye protection.
OTHER
PROTECTIVE CLOTHING OR EQUIPMENT
Use impermeable
aprons and protective clothing whenever possible to prevent skin contact. The
use of head caps whenever possible is strongly recommended.
WORK/HYGIENIC
PRACTICES
Eye washes
and safety showers in the workplace are recommended.
SECTION
VIII - DISCLAIMER
To the best
of our knowledge, the information contained herein is accurate, obtained from
sources believed by Cumberland Products Inc. to be accurate.